Electrolytic Capacitor 10 uF 63V, Ceramic Capacitor 30 pF, Ceramic Capacitor 104 pF, 100 uF 63V Capacitor, Electrolytic, 14 Pin Chassis Mount Female Connector, MS3102R 24 27S, 14 Pin Cable Mount Male Connector, MS3106R 24 27P, 5 Pin Cable Mount Female Connector Part, No MS 3106 14S 5S, 5 Pin Chassis Mount Male Connector, Part No MS 3102 14S 5P, 3 Pin Chassis Mount female, Connector Part No MS 3102R 10SL 3P, 3 Pin cable Mount, male Connector Part No MS 3102F 10SL 3S, 64 Pin Right, Angle EURO Connector Male, 64 Pin Straight EURO, Connector Female, ITP 20 Pin Male Connector, ITP 20 Pin, Female Connector with Cable, 22 point 118 MHz Crystal, Fuse 6Amp Fuse 32 mm long, Fuse Holder for 32 mm long, Fuse, AT89C55WD, LTC 1334 Driver IC, PA61 Module, 28, pin IC Base Wide Round Machine Hole, 40 pin IC Base Wide, Round Machine Hole, 14 Pin IC Base Narrow Round Machine, Hole, 16 pin IC base Round Machine Hole Narrow, 20 pin IC, base Round Machine hole Narrow, EMI Ferite Beads and, Impedance is equal to 90 Ohms, LED green 5mm dia, LED, Yellow 5mm dia, LED Red 5mm dia, LED blue 5mm dia, LED Holder for 5mm dia led, Digital to Resolver or Synchro, Converter PCB in FR4 Gerber File as per WESEE Design, 10K Top Tune Pot, 50K Top Tune Pot, 10K Resistor Pack 9, Pin, 10K Resistor Pack 5 Pin, 500E Resistor 1 by 4 watt, Tolerance 1 percent, 270E Resistor 1 by 4 watt Tolerance, 1percent, 470E Resistor 1 by 4 watt Tolerance 1percent, 1, point 5K Resistor 1 by 4 watt Tolerance 1percent, 82K, Resistor 1 by 4 watt Tolerance 1percent, 1K Resistor 1 by 4, watt Tolerance 1percent, 10K Resistor 1 by 4 watt, Tolerance 1percent, 4 Point 7K Resistor 1 by 4 watt, 5K Resistor 1 by 4 watt Tolerance, 820E Resistor 1 by 4 watt Tolerance 1percent, 200E Resistor 1 by 4 watt Tolerance 1percent, ON or OFF, DPDT Toggle Switch 20A, ON or OFF DPDT Toggle Switch 5, Amp, IN4148 Signal Diode, 1N4007 Diode, 15 point 1 V, Zener Diode, Cosel Power Supply LDC60F 2 Plus 5V Plus, 15V Negative 15V, 6 Amps Power Cords, 3x10 mm SS, Screw Star Head, 3x10mm Screw round Head, 3 mm SS, nuts, 3 mm SS Washer, 3mm Dia Fiber Washer, 3 cm Long, Spacer with one side 3mm dia screw, 3 cm Brass Spacer, Both side holes for 3mm screws, 2 point 5 cm Long Spacer, with both side 3 mm hole, 2 point 5 Cm Long brass Spacer, with one side 3 mm hole, Cable Tie 10 inch, Solder Wire in, KG, Glue Stick, Rugged Enclosure with Cooling as per, WESEE Design, DSC11525 Make DDC